SOME SPECIFICATIONS

5 April 2016

ALL TEST EQUIPMENT – to be inspected by the Jury for approval

 

PLUG GAUGES

ISSF & PA events

4.5 mm:

5.6 mm:

CF:

+0.05/-0.00 mm

 

 

NRA & WA1500

.32:

9 mm/.38/.357:

+0.05/-0.00 mm

 

OVERLAYS

As approved by the NRC

 

 

 

 

 

 

TIMERS

Face time

Specified time +0.2/-0.0 seconds

 

Away time – CF/Sport/PA

7 +/- 0.1 seconds

 

Away time – completion of series

Stay away until ‘face’ initiated by Range Officer

 

Away time – at completion of RFP Finals series

7 +/- 0.1 seconds

 

 

 

 

TRIGGER WEIGHTS

Specified weight +0.0/-2.0 g

 

 

 

 

 

 

RANGE AND TARGET DIMENSIONS – to be checked by the Jury

 

 

Distances & Target heights to centre

 

Distance

Height

10 m

10 m +/- 0.05 m

1.40 m +/- 0.05 m

 

25 m

25 m +/- 0.10 m

1.40 m 0.10 m / - 0.20 m

 

50 m

50 m +/- 0.20 m

0.75m +/- 0.50m

 

7 yards

6.40 m +/-50 mm

1.40 m +/- 50 mm

 

10 yards

9.14 m +/-50 mm

1.40 m +/- 75 mm

 

25 yards

22.85 m +/-100 mm

1.40 m +/- 200 mm

 

PA SERVICE PISTOL TARGET DIMENSIONS

The black target zone is 76cm high and 45 cm wide, however the target should be surrounded by a white edge about 1 cm wide, totalling the target card to be a minimum of 78 cm x 47 cm. The top edge of the scoring area begins at the upper midpoint in the 6 ring and ends at the lower midpoint of the 6-ring at the bottom of the target.. It is divided into 5 scoring zones by white scoring lines approximately 1 mm thick. The central 10-point scoring zone is formed by two vertical lines each 5 cm long, 10cm apart and joined at their upper and lower ends by semicircles with a 5cm radius. The 10-point scoring zone is, therefore, 10 cm wide and 15 cm high. The scoring zones from 9 to 6 are similarly shaped. Their widths are successively increased by 10 cm (5 cm on either side) and their heights by 15 cm (7.5 cm, at the top and 7.5 cm at the bottom). The Centre of the 10-zone must be 37.5 cm from the top edge of the 6-ring. A tolerance deviation of +/- 0.5 mm is allowable for the dimensions of the 10-zone and +/- 1 mm for the other scoring zones. The zones are measured from the outside edge of the scoring lines. The scoring zones are marked with numbers corresponding to the value in points they represent (9, 8, 7, 6). Hits in the black corner of the zones outside the 6 ring shall be scored as zeros.

The score value numbers must be printed in four horizontal and vertical directions at right angles to each other. The figures should be 30 mm high and 15 mm wide with a printing thickness of approximately 2 mm. The 10-zone is not numbered.

Overall size of target

470 x 780 mm

Minimum

Black target area

450 x 760 mm

Minimum

White edge

10 mm

Minimum

X ring (optional)

50 x 75 mm +/-0.5 mm

Line width for ring and 'X', approx. 0.5 mm wide

10 ring

100 x 150 mm +/-0.5 mm

Line width for 10 ring approximately 1 mm wide

9 ring

200 x 300 mm +/- 1.0 mm

Line width for rings approximately 1 mm wide.

The figures '9' to '6' should be 30 mm high and 15 mm wide with a printing thickness of approximately 2 mm.

8 ring

300 x 450 mm +/-1.0 mm

7 ring

400 x 600 mm +/-1.0 mm

6 ring

(500) x 750 mm +/- 1.0 mm

Note 1: the 'X' ring count is not used for Service Pistol, Service Pistol Unrestricted, or Black Powder.

Note 2: Note 3: the X-ring and the 'X' are printed with 0.5 mm print width.

© 2016, Pistol Australia Inc.  – Copyright information>